Стандарты Cummins Genset Technical Maintenance-3
Если изгибов трубопровода слишком много, диаметр выхлопного трубопровода необходимо увеличить.
F. Если шум затвора нужно убавить заранее, возможна установка глушителя 2-го класса. (см. изображение 3)
(Рисунок 3: A. The exhaust pipeline can be moved freely within the frame.
В. The frame can support the muffler, but the two cannot be fixed.
С. bellow
Heat-preventing materials / lined board / глушитель / bracket)
5.5 FDK-Cummins Genset Installation Mode Pattern:
(Single genset with soundproof 85dBA within 1 meter/ see Picture 4)
Рисунок 4: (upwards上部图)
С: genset neutral line/ M: cable ditch /FGY: air entry / J: cable ditch to the power distribution room/ B: soundproof door/ A: pipeline for fuel conveyer (while using the oil storage tank )
(Downwards下部图)
С: exhaust pipeline / inner and outer guards / exhaust pipeline hanging rack/ thermal insulation materials and alloy outer guards / bellow
грамм: airflow / exhaust muffler / oil tank of genset chassis (choose)
K: airflow / entry muffler / shutter / cable ditch
5.6 Genset Installation Model in Particular condition:
(см. изображение 5: Radiator Installation / Рисунок 6: Heat Converter Installation)
Рисунок 5:
Cooling for far-placed water tank / inflation water tank / radiator fan by motor start
Заметка: The height for radiator installation is hinged on the type of genset ventilation fan
Cooling for far-placed water tank—-high-placed
Roof / wholly-sealed and far-placed water tank
Заметка: the height for radiator installation is henged on the situation of installation.
Motor pump/ stopping valve /soft connection/ heat converter / soft connection /water tank for genset cooling and supplying loop
Заметка: The circulation of air in the generator room must be in better condition so that the radiated heat can be taken away from the genset and the air for burning in genset can be supplied.
Рисунок 6
Heat:
Cooling / water tower/ water pond / heat converter
5.7 Installation Requirement for Fuel Supply System:
A. Fuel tank for daily use together with oil storage tank can be adopted for 8 hours‟ working whose volume is calculated as: the genset rated power times 2.7 литры.
В. The fuel tank for daily use must be 1 meter higher than the genset installation plane, but not too high, so as to prevent its pressure from exceeding the load of the genset fuel pump.
С. The exit of the oil storage tank must be 75 mm above the fuel tank bottom.
D. The bottom of the oil storage tank must lean over 30 mm to the ground so as to prevent its inside from accumulating and absorbing dust into the daily-use fuel tank. It‟s also convenient for removing different obstacles.
Е. When the oil storage tank full, after 48 hours sediment, the accumulated dust and water inside must be discharged before reuse.
Fuel-feed System (Рисунок 7-8)
2008-06-22
122
(Left—-Right从左到右/ Up—-Down从上到下)
Ventilation exit / exhaust valve/ refueling pipe/ oil volume indicator /overhauling place /
Leaning / stick or steel structural support / filter / fuel-feed valve / fuel-feed pipe / not lower than 500 мм / soft connection / генератор
Fuel-feed System Pattern
(Without neutral fuel tank)
Ventilation exit / выхлопной клапан / large-scale oil storage tank / refueling pipe / oil volume indicator / overhauling place /leaning / stick or steel structural support / overflowing connection ( to dust-collected pond)
Overflowing pipe / fuel-feed valve / double pump / filter /discharge gate / dust-collected pond / neutral fuel tank / volume switch / fuel-feed pipe / oil-setback pipe / soft connection / генератор
Fuel-feed System Pattern (With Neutral fuel tank)
6.1 Installation ways are uncovered, inside cable slot, buried, laid and mixed with multi-lines.
6.2 The end line of genset must be connected with soft cable so as to reduce the vibration frequency of genset. If there‟s some distance between the switch and the genset, a cable connection box can be installed beside the genset so that the length of the soft cable line may be saved. A cable connection box can be applied among the connection box, the switch screen and the electrical distribution screen, so that some expenditure can be decreased.
7. Regulation for Electronic Governor
The genset FDK Co. manufactured are equipped in engine with partly mechanical governor and partly electronic one. The power of both of them is quality and quantity guaranteed. This will bring the best convenience for the genset to accomplish the auto control functions such as auto paralleling control, и т.д.
Every engine with electronic governor of FDK Co. is all to be regulated, so customers do not have to perform this kind of process except after the future general maintenance or if some probable breakdown happens to the electronic governor.
The Control Unit of Governor Installed in the Control Cabinet of Genset (см. изображение 9)
Рисунок 9: (Left—-Right从左到右)
Transducer / performer/ rotation speed/ gain /stability/ governor /idling system/ inner tachometer after dispatching rubber cover/ gain / stability
A. Place switch “C1” to “On”, if something of drifted away while moving, place “C2” to „Off”.
В. If everything OK, place “C2” to “On”.
С. Turn the “Gain” and “Stability” to the intermediate.
D. Connect terminal “L” with “M” temporarily.
7.1 Regulation after the Electronic Governor‟s Start
While the engine is in the style of cold, regulate the fuel throttle draw bar suitably, the rotation speed is to be altered .Generally, the speed is at its speed around 1500 оборотов в минуту. After a period of rotation of the genset till the water temperature rises progressively, the degree of throttle must be let down so as to keep its rotation at the speed of 1500±10 rpm. And this degree is exacting the rated rotation speed of the genset.
7.2 On the genset instrument panel is installed a frequency meter. In general, if any meter of rotation speed is not installed, the rotation speed can be calculated as the following formula:
Tachometer “n”= F × 60/p
(“P” —-synchronous genset pole logarithm, e.g. 4-pole genset “P” is 2.)
Похожие материалы
